Lush Food & Drink

Explainer

Why is my pellet grill not getting hot?

Most often the controller is holding a set temperature, the fire pot is starved of air or pellets, or the grill is losing heat faster than the burner can replace it.

By the Lush Editorial Team·Researched & Compared

A pellet grill that will not get hot is usually being held at a set temperature by its controller, or its fire pot is not getting enough air and fuel to burn cleanly. The maker’s published temperature range tells you what the grill is built to reach, and anything below that points to the controller setting, the fire pot, or heat loss rather than a fault in the design.

The grills compared in Best Pellet Grills and Smoke Tubes for Backyard Cooks publish different levels of detail about how they hold heat, and it is worth reading what each one actually states before you start taking anything apart.

Check the controller setting first

The single most common reason a pellet grill sits at a low temperature is that the controller is doing its job. Traeger publishes that the Pro 22 runs from 180°F to 450°F within plus or minus 15 degrees, so a grill set to 180°F or 225°F is not failing to get hot, it is holding the temperature it was told to hold. If you expected searing heat, the set point is the first thing to look at.

Z GRILLS describes its 7002C as using a PID 3.0 controller with an LCD screen that auto-tunes fuel and airflow to keep temperature consistent when outside temperatures move. That is a controller that will deliberately feed less fuel when the grill is near its target, so a low reading on a display can reflect a low target rather than a weak fire.

Neither maker publishes a maximum temperature for these two grills beyond the Traeger range above, so this site has not compared a top-end figure for the Z GRILLS unit. If your grill is set high and still reads low, move on to the fire pot.

Air and fuel at the fire pot

A pellet grill makes heat by burning pellets in a fire pot with air blown through them. If the pot is full of ash, the air holes are blocked, or the pellets have absorbed moisture, the fire smolders instead of burning and the grill never reaches its set point. Empty the pot, clear the air holes, and use dry pellets before assuming anything is broken.

Pellet supply matters too. Z GRILLS publishes a 28 lbs pellet hopper on the 7002C and a view window so you can monitor supply without lifting the lid, and Traeger publishes an 18 lbs hopper on the Pro 22 with a clean-out door for fast flavor swaps. A hopper that has bridged, with pellets stuck above an empty auger, will starve the fire while looking full from above.

Traeger also publishes a built-in meat probe on the Pro 22 for monitoring internal food temperature without opening the lid, and Z GRILLS publishes two included meat probes with its LCD screen. Every time the lid comes up, heat leaves the cooking chamber, so a grill that is checked constantly will struggle to hold temperature.

Heat loss around the cooking chamber

A pellet grill in cold, windy or wet weather loses heat faster than the fire can replace it. Z GRILLS states that its PID 3.0 controller auto-tunes fuel and airflow for temperature consistency despite significant external temperature variations, which describes the controller compensating, not the chamber being insulated. Wind across the lid and vents is the usual culprit.

Traeger publishes powder-coated steel construction and porcelain-coated grill grates on the Pro 22, and Z GRILLS publishes sturdy steel construction with a high-temperature powder coating finish on the 7002C. Neither maker publishes an insulation rating or a chamber volume for these grills, so this site has not compared how each holds heat in cold conditions.

Practical steps follow from the construction: move the grill out of the wind, keep the lid closed, and give the controller time to respond. A grill that reaches temperature on a still day and stalls on a windy one is telling you about its surroundings, not its burner.

Adding smoke without adding heat

Some cooks confuse smoke output with heat. A pellet tube or smoker box adds smoke flavor and does not raise the grill temperature, so if the complaint is thin smoke rather than low heat, a tube is the right tool. The LIZZQ Premium Pellet Smoker Tube measures 12 inches long and 2.16 inches wide, and the maker states it can produce smoke for up to 5 hours.

The Napoleon PRO Stainless Steel Smoker Pipe measures 12 inches by 1.75 inches by 1.75 inches and is designed to sit on the sear plates of a gas grill above a burner. The Weber Premium Universal Smoker Box measures 9.8 inches by 4.5 inches by 2 inches and is built to fit most sizes of grill. None of these three is a heat source for a pellet grill.

If your pellet grill is running at its set temperature but the food lacks smoke, a tube loaded with pellets and lit at one end will smolder alongside the cook. It will not fix a grill that is genuinely cold.

What the makers do and do not publish

The published figures cover cooking area, hopper capacity, dimensions and, for Traeger, a temperature range. Z GRILLS publishes 697 sq in of grilling space on the 7002C, and Traeger publishes 572 sq in on the Pro 22. Those numbers describe capacity, not heat output, and neither maker publishes a BTU or wattage figure for these grills in the material compared here.

Z GRILLS publishes a hopper cleanout for emptying the hopper and swapping pellet flavors, and Traeger publishes a clean-out door for the same purpose. Both are worth using: old pellets in a humid hopper are a common cause of a weak fire, and the makers give you a way to clear them.

Where a maker publishes nothing, this site has not compared it. That applies to maximum temperature on the Z GRILLS 7002C, to insulation on both grills, and to any published burn rate. Work from the set point, the fire pot and the weather, in that order, and the cause is usually found without a repair.

Common questions

What temperature should a pellet grill reach?

Traeger publishes a range of 180°F to 450°F within plus or minus 15 degrees for the Pro 22. Z GRILLS does not publish a maximum temperature for the 7002C in the material compared here, so this site has not compared a top-end figure for that grill. Check your controller set point against the range your maker publishes.

Why does my pellet grill stay at 225°F?

Because 225°F is a smoke setting, not a fault. A controller holding a low set point feeds pellets slowly to keep the chamber there. Raise the set point and give the grill time to climb. If it will not climb with a high set point, clear the fire pot and check the air holes.

Can a smoke tube make my pellet grill hotter?

No. A smoke tube adds smoke flavor only. The LIZZQ tube measures 12 inches by 2.16 inches and the maker states up to 5 hours of smoke. It sits alongside the cook and smolders; it does not raise the temperature of the cooking chamber.

Why does my grill lose heat when it is windy?

Wind pulls heat off the lid and through the vents faster than the fire replaces it. Z GRILLS states its PID 3.0 controller auto-tunes fuel and airflow to hold temperature despite significant external temperature variations, but neither maker publishes an insulation rating for these grills. Move the grill out of the wind.

How full should the hopper be?

Z GRILLS publishes a 28 lbs hopper on the 7002C and Traeger publishes an 18 lbs hopper on the Pro 22. Keep pellets above the auger intake and check for bridging, where pellets stick above an empty auger. Both makers publish a cleanout so you can empty old pellets.

Does opening the lid drop the temperature?

Yes. Heat leaves the chamber every time the lid comes up. Traeger publishes a built-in meat probe on the Pro 22 and Z GRILLS publishes two meat probes with its LCD screen, both for reading food temperature without lifting the lid. Use them and keep the lid closed.

Ready to compare actual models?

Our buying guide puts five products side by side on the numbers their makers publish.

More questions about pellet grills and smoke tubes