Explainer
How do you clean under-sink water filters?
You do not really clean the filter cartridge itself, it is a sealed, replaceable element that you swap out when exhausted. What you clean is the housing: shut off the water, release the pressure, unscrew the housing, wash it in warm soapy water (and sanitize it), then fit a new cartridge. So maintenance is replacing the cartridge and washing the housing, on schedule.
By the Lush Editorial Team·Researched & Compared
With an under-sink water filter, you do not really clean the filter cartridge itself, because the cartridge is a sealed, consumable element (packed with media like carbon that traps contaminants) that you cannot wash clean, instead, you replace it with a new one when it is exhausted (on its schedule). What you do clean is the filter housing (the canister the cartridge sits in) when you change the cartridge. The process is: shut off the water supply to the filter, release the pressure (open the filtered-water faucet or press the pressure-release button if the unit has one), unscrew or unclip the housing (using the housing wrench if provided) and catch the water in it, remove and discard the old cartridge, wash the housing out with warm soapy water (scrubbing off any sediment or slime), rinse it well, and ideally sanitize it (a little diluted bleach solution or the manufacturer’s recommended sanitizer, then rinse thoroughly), then insert the new cartridge (check the O-ring is clean and seated), screw the housing back on, turn the water back on, and run the filter for a few minutes to flush the new cartridge and check for leaks. So cleaning an under-sink water filter really means replacing the cartridge and cleaning the housing during that change, done on the cartridge’s schedule, rather than washing a reusable filter. So the key maintenance is timely cartridge replacement plus washing and sanitizing the housing. Our Best Under-Sink Water Filters compares five of them. (Follow your filter’s own manual, as designs vary.)
Why you replace the cartridge rather than clean it
The core thing to understand is that an under-sink water filter’s cartridge is not something you clean, it is a consumable you replace. The cartridge is a sealed element filled with filter media (such as activated carbon, and sometimes sediment media or other stages) that works by trapping and adsorbing contaminants (chlorine, sediment, certain chemicals, odors and tastes) as water passes through. Over time the media fills up with what it has removed and becomes exhausted, its capacity used up, and you cannot wash that out or regenerate it, the trapped contaminants and the spent media mean the cartridge must be replaced with a fresh one to keep filtering effectively.
So trying to clean the cartridge to reuse it does not work (and would be unhygienic, a used cartridge can harbor bacteria) and is not how these filters are maintained. Instead, you replace the cartridge on the schedule the manufacturer gives (based on time, often every several months to a year, or on gallons filtered), because a cartridge left in past its life stops filtering well and can become a hygiene problem. So the main maintenance is timely cartridge replacement, not cleaning the cartridge. Understanding this reframes the question: cleaning an under-sink filter means cleaning the housing and fittings when you do a cartridge change, which the next sections cover. So do not try to wash and reuse the cartridge, swap it out on schedule, and clean the housing while you are at it. So the cartridge is replaced, the housing is cleaned.
The cartridge change and cleaning the housing
Here is the practical process, which combines replacing the cartridge with cleaning the housing (always follow your filter’s own manual, as designs differ). First, shut off the water supply to the filter (there is usually a valve on the cold-water line feeding it, or shut off the main). Then release the pressure in the system by opening the filtered-water faucet (and press the housing’s pressure-relief button if it has one) so water stops and the housing is not under pressure. Place a towel or shallow pan under the unit to catch drips.
Next, unscrew or unclip the filter housing (the canister), many units come with a housing wrench to loosen it, and lower it carefully as it holds water. Remove the old cartridge and discard it. Now clean the housing: empty it, and wash the inside with warm water and a little dish soap, using a soft brush or cloth to remove any sediment, slime or buildup, then rinse thoroughly. For hygiene, sanitize the housing, a common method is a solution of a small amount of unscented bleach in water (per the manufacturer’s guidance) swirled in the housing, then rinsed very thoroughly with clean water (or use the sanitizer the maker recommends). Also wipe the O-ring seal and its groove (keep the O-ring clean and undamaged, lightly lubricate with food-safe silicone grease if the manual says, as a clean, intact O-ring prevents leaks). So the housing gets washed and sanitized while the cartridge is out. So this is the actual cleaning step of under-sink filter maintenance. So clean and sanitize the housing, then move to fitting the new cartridge.
Fitting the new cartridge and finishing
With the housing cleaned and sanitized and the O-ring clean and seated, insert the new cartridge into the housing (make sure it is the correct replacement for your model, and oriented correctly if it has a direction). Screw or clip the housing back onto the filter head, hand-tight plus a careful turn with the wrench if needed (do not overtighten, which can damage the O-ring or housing). Make sure everything is seated properly.
Then turn the water supply back on slowly, and check carefully for leaks around the housing and connections (tighten a little more or reseat the O-ring if it weeps). Finally, run the filter, open the filtered-water faucet and let it run for a few minutes (the time the manufacturer specifies) to flush out any carbon fines, loose particles or air from the new cartridge and to rinse away any sanitizer residue, until the water runs clear. Your filter is now serviced: new cartridge in, housing cleaned. Note the date (or set a reminder) for the next cartridge change. So the full picture of cleaning an under-sink water filter is: replace the (non-cleanable) cartridge on schedule, and during that change, wash and sanitize the housing and keep the O-ring clean, then flush the new cartridge. So it is really scheduled cartridge replacement plus housing cleaning, not washing a reusable filter. So maintain it on schedule and clean the housing each time, and your filter stays effective and hygienic. So that is how you clean an under-sink water filter.
The short answer
With an under-sink water filter, you do not clean the cartridge itself, it is a sealed, consumable element (filled with media such as activated carbon that traps contaminants) that you cannot wash clean, so you replace it with a new one when it is exhausted, on the schedule the manufacturer gives (often every several months to a year, or by gallons filtered). A cartridge left in too long stops filtering well and can harbor bacteria, so timely replacement is the key maintenance. What you actually clean is the housing (the canister) when you change the cartridge. The process (follow your unit’s manual, as designs vary): shut off the water supply to the filter, release the pressure by opening the filtered-water faucet (and the pressure-relief button if fitted), put a towel underneath, then unscrew or unclip the housing (using the housing wrench if provided) and lower it carefully as it holds water. Remove and discard the old cartridge, wash the housing inside with warm soapy water to remove sediment and slime, rinse well, and sanitize it (a little diluted unscented bleach per the maker’s guidance, or the recommended sanitizer, then rinse thoroughly). Wipe the O-ring and its groove and keep it clean and intact to prevent leaks. Then fit the correct new cartridge, screw the housing back on (hand-tight, not overtightened), turn the water back on slowly, check for leaks, and run the filtered-water faucet for a few minutes to flush the new cartridge and any sanitizer. So cleaning an under-sink water filter really means scheduled cartridge replacement plus washing and sanitizing the housing during that change.
Common questions
How do you clean an under-sink water filter?
You do not clean the cartridge, you replace it on schedule, and you clean the housing during the change. Shut off the water to the filter, release the pressure (open the filtered-water faucet), unscrew or unclip the housing (using the wrench if provided) and catch the water, remove the old cartridge, wash the housing in warm soapy water and sanitize it (diluted unscented bleach or the recommended sanitizer, then rinse), fit a new cartridge with a clean O-ring, reassemble, turn the water on, and flush the new cartridge for a few minutes. Always follow your unit's manual.
Can you clean and reuse a water filter cartridge?
No. The cartridge is a sealed, consumable element packed with media (such as activated carbon) that traps and adsorbs contaminants as water passes through, and once the media is full and exhausted you cannot wash it out or regenerate it. Trying to clean and reuse it does not restore its filtering and is unhygienic, a used cartridge can harbor bacteria. So you replace the cartridge with a fresh one on the manufacturer's schedule (by time or gallons) rather than cleaning it. The cleaning you do is of the housing, not the cartridge.
How often do you replace an under-sink filter cartridge?
On the schedule the manufacturer specifies, which is commonly every several months up to about a year, or based on the volume of water filtered (gallons), and varies by filter type, cartridge capacity and your water usage and quality. A cartridge left in past its life stops filtering effectively and can become a hygiene problem, so replace it on time. Check your filter's manual for its exact interval, note the date when you change it, and set a reminder for the next change so you do not forget, since timely replacement is the main maintenance.
How do you clean the filter housing?
When you change the cartridge, after shutting off the water, releasing the pressure and removing the old cartridge, empty the housing and wash the inside with warm water and a little dish soap, using a soft brush or cloth to remove sediment, slime or buildup, then rinse thoroughly. For hygiene, sanitize it, a common method is a small amount of unscented bleach in water (per the maker's guidance) swirled in and then rinsed very thoroughly with clean water, or the sanitizer the manufacturer recommends. Also wipe the O-ring and its groove and keep the O-ring clean and intact to prevent leaks.
What do you do after fitting a new cartridge?
Make sure the O-ring is clean and seated and the new cartridge is the correct one and oriented right, screw or clip the housing back on hand-tight (plus a careful turn with the wrench if needed, without overtightening), then turn the water supply back on slowly and check carefully for leaks around the housing and connections. Finally, run the filtered-water faucet for a few minutes (the time the manufacturer specifies) to flush out carbon fines, loose particles and air from the new cartridge and rinse away any sanitizer residue, until the water runs clear. Then note the date for the next change.
Ready to compare actual models?
Our buying guide puts five products side by side on the numbers their makers publish.