Lush Food & Drink

Buying Guide ·Organization

Best Pullout Cabinet Baskets for Reaching Without Kneeling

The deciding specification is what each maker publishes about the load and what fixes the unit to the cabinet, because only one of these five gives a load figure and it is held on by suction cups.

By the Lush Editorial Team·Researched & Compared

  • Researched & ComparedSpecs pulled from the manufacturer listing
  • Like-for-LikeSame measures across every model
  • No Paid PlacementsNobody pays to appear here

Compared the sixteen pullout listings on the fact sheet by the load each maker publishes, what fixes the unit to the cabinet, and which slides are stated to close softly.

Our shortlist

Five products, one set of published numbers.
  1. PXRACK Under Sink Organizer
    Best for a published load and no drilling

    PXRACK Under Sink Organizer

    Up to 60 lbs on four suction cups and two adhesive films, across three tiers.

    • PXRACK
    • 3-Tier(2 Packs)
    • 10.96 lb
  2. ClosetMaid 32105 Premium Wide 3-Tier Compact Kitchen...
    Best for glides stated to close softly

    ClosetMaid 32105 Premium Wide 3-Tier Compact Kitchen...

    The only soft close glides here, on three tiers with four compartments.

    • ClosetMaid
    • 8.75-Inch
    • 9.2 lb
  3. Rev-A-Shelf Pullout Organizer for Cabinets
    Best for four screws and two steel baskets

    Rev-A-Shelf Pullout Organizer for Cabinets

    Fully assembled, fixed with four screws, at 19.75 pounds, the heaviest unit of these five.

    • Rev-A-Shelf
    • 12" W x 22"D
    • 19.75 lb
  4. Pull out Cabinet Organizer
    Best for getting off your knees in a frameless cabinet

    Pull out Cabinet Organizer

    Nano glue instead of screws, leather handles and 6.2 inch sidewalls, at 4.61 pounds.

    • Kitstorack
    • 11.8"Wide-15.7"Deep (1Pack)
    • 4.61 lb
  5. OCG 2 Tier Pull Out Cabinet Organizer (15.5" W x 21"...
    Best for two tiers that move independently

    OCG 2 Tier Pull Out Cabinet Organizer (15.5" W x 21"...

    Upper and lower baskets on separate ball bearing slides, with two heights for the lower.

    • OCG
    • 15.5"W x 21"D, 2 Tier
    • 12.9 lb

Side by side

Blank means the maker does not publish it.
ModelBrandSize (capacity)WeightBest for
PXRACK Under Sink Organizer PXRACK 3-Tier(2 Packs) 10.96 lb Best for a published load and no drilling
ClosetMaid 32105 Premium Wide 3-Tier Compact Kitchen... ClosetMaid 8.75-Inch 9.2 lb Best for glides stated to close softly
Rev-A-Shelf Pullout Organizer for Cabinets Rev-A-Shelf 12" W x 22"D 19.75 lb Best for four screws and two steel baskets
Pull out Cabinet Organizer Kitstorack 11.8"Wide-15.7"Deep (1Pack) 4.61 lb Best for getting off your knees in a frameless cabinet
OCG 2 Tier Pull Out Cabinet Organizer (15.5" W x 21"... OCG 15.5"W x 21"D, 2 Tier 12.9 lb Best for two tiers that move independently

Each pick in detail

What the listing says for it, and against it.
1 Best for a published load and no drilling

PXRACK Under Sink Organizer

Up to 60 lbs on four suction cups and two adhesive films, across three tiers.

  • For it
  • The only pick here to publish a load, stating it holds up to 60 lbs effortlessly
  • Publishes four large suction cups and two nano adhesive films, so nothing is drilled
  • Publishes five or more height settings across three tiers, which no other pick matches
  • States you can reach items at the back without bending or kneeling, and names a 1 in reinforced frame
  • Against it
  • Publishes no unit size in words at all, only a carton of 12 by 16 by 15.4 inches
  • Publishes no cabinet opening figure, so whether it fits has to be worked out from the carton
  • Publishes nothing about how long suction cups hold 60 lbs in a damp under sink cabinet
2 Best for glides stated to close softly

ClosetMaid 32105 Premium Wide 3-Tier Compact Kitchen...

The only soft close glides here, on three tiers with four compartments.

  • For it
  • The only pick here with soft close glides, on ball bearing full extension runners
  • Publishes an installed size of 18.36 by 8.82 by 17.98 inches and a minimum 9 in opening
  • Includes a template that gives the exact location for installation, plus the hardware
  • Publishes three tiers and four compartments, stated for tall items like bottles
  • Against it
  • Publishes no load figure, on a three tier unit sold for cleaning supplies and containers
  • Publishes 9.2 lb of unit before anything is stored, and it mounts into the cabinet floor
  • Publishes no handle, so the basket is pulled by the wire
3 Best for four screws and two steel baskets

Rev-A-Shelf Pullout Organizer for Cabinets

Fully assembled, fixed with four screws, at 19.75 pounds, the heaviest unit of these five.

  • For it
  • Comes fully assembled and states a simple four screw installation with the hardware included
  • Publishes a full extension ball bearing system on each of its two steel baskets
  • States the organizer can be pulled all the way out of a cabinet
  • Publishes a minimum opening width of 11.5 in and tells you to measure including the hinges
  • Against it
  • Publishes 19.75 lb, the heaviest unit of these five, before a single pan goes in it
  • Its own text gives four different sizes, and its dimension fields read a depth of 1 inch
  • Publishes no load figure and no soft close, only heavy duty slides

Who should skip this: Skip this if weight matters: at 19.75 lb it is the heaviest of the five published weights.

4 Best for getting off your knees in a frameless cabinet

Pull out Cabinet Organizer

Nano glue instead of screws, leather handles and 6.2 inch sidewalls, at 4.61 pounds.

  • For it
  • States you no longer need to be on your knees to reach the back of a lower shelf
  • Publishes 4.61 lb, the lightest unit of these five, so installation is a one person lift
  • Publishes 3 stage full extension ball bearing slides and 6.2 in sidewalls against spills
  • The only pick here with a handle claim, stating premium leather handles
  • Against it
  • States it fits frameless cabinets only and will not fit a cabinet with a framed door
  • Publishes no load figure, only excellent load bearing strength in words
  • Holds itself in with nano glue, so the load rests on an adhesive rather than screws
5 Best for two tiers that move independently

OCG 2 Tier Pull Out Cabinet Organizer (15.5" W x 21"...

Upper and lower baskets on separate ball bearing slides, with two heights for the lower.

  • For it
  • Publishes upper and lower baskets that slide out independently on precision ball bearing slides
  • Publishes two height options for the lower basket, so a tall pan can be planned for
  • States a unit of 15.5 by 21 by 15.6 inches and the opening and depth it needs
  • Comes with a step by step manual, a mounting template and all the hardware
  • Against it
  • Publishes no load figure, on the pick sold for pots, pans and small appliances
  • Asks for at least 16.5 in of opening and 22 in of depth, the largest cabinet demanded here
  • Publishes 12.9 lb of unit and no handle, so the wire is what you pull

Who should skip this: Skip this if counter or storage space is tight: it has the largest published footprint of the five, 21 by 15 inches.

Our verdict

PXRACK is the only one of these five to publish a load, at 60 lbs, and it is held on by four suction cups and two adhesive films. ClosetMaid is the only one with soft close glides. Rev-A-Shelf fixes with four screws and publishes 19.75 pounds of unit. Kitstorack states you no longer need to be on your knees, and OCG slides each tier out separately.

“One load figure, and suction cups hold it up.”

Lush Editorial Team

What separates these five

One load figure in sixteen listings PXRACK states it holds up to 60 lbs. Kitstorack says excellent load bearing strength with no number, and Rev-A-Shelf says heavy duty slides. ClosetMaid and OCG say nothing about load at all.
The load sits on suction cups The one pick that publishes a load is also the one held on by four suction cups and two adhesive films. Rev-A-Shelf, ClosetMaid and OCG all screw in and none of the three publishes a load.
One set of soft close glides ClosetMaid publishes ball bearing full extension soft close glides. The other four publish smooth, quiet, precision or 3 stage slides, and none of them mentions how the basket stops.
Unit weights from 4.61 to 19.75 pounds Kitstorack publishes 4.61 pounds, ClosetMaid 9.2, PXRACK 10.96 for two packs, OCG 12.9 and Rev-A-Shelf 19.75. That is the mass on the slides before anything is stored.
Two listings say what the point is PXRACK states you can reach the back without bending or kneeling. Kitstorack states you no longer need to be on your knees. Those two sentences are the only ones on this sheet about the body rather than the cabinet.

How we chose

Priorities, not a computed score. The inputs are published specifications, so we rank by what matters most and say how much.

  1. 30% Load publishedA basket you lean on should say what it will take
  2. 25% Fixing method publishedAdhesive, suction cups and screws are not the same promise
  3. 20% Soft close publishedA heavy tier that slams is a trapped finger
  4. 15% Unit weight publishedIt is what you hold up inside the cabinet to install it
  5. 10% Cabinet opening publishedOne of these five names no opening figure at all

How the Five Compare on the Numbers

A pullout basket is the answer to a cabinet you cannot see into, and the accessible question is what happens when you put weight on it. Only one of these five publishes a load figure. PXRACK states 60 lbs, and it is the one held to the cabinet by suction cups and adhesive rather than screws. The other four publish nothing.

The unit weights run wide. Kitstorack publishes 4.61 pounds, ClosetMaid 9.2, PXRACK 10.96 for two packs, OCG 12.9 and Rev-A-Shelf 19.75. That figure matters twice over: it is what you lift into the cabinet during installation, and it is the mass already on the slides before anything goes in at all.

Published specification PXRACK 3 tier organizer ClosetMaid 3 tier basket Rev-A-Shelf two basket pullout Kitstorack adhesive drawer OCG 2 tier organizer
Load published Up to 60 lbs not published not published, heavy duty slides not published, load bearing strength not published
What holds the unit in the cabinet Four suction cups and two adhesive films A template and hardware, mounted to the cabinet floor Four screws, comes fully assembled Nano glue, no screws or drilling A mounting template and all the hardware
Slide type published A smooth 3 tier sliding design Ball bearing full extension glides A full extension ball bearing system on each basket 3 stage full extension ball bearing slides Precision ball bearing slides, tiers move independently
Soft close published not published Soft close glides not published not published not published
Published unit weight 10.96 lb for two packs 9.2 lb 19.75 lb 4.61 lb 12.9 lb
Unit size the maker states not published, a carton of 12 x 16 x 15.4 in 18.36 x 8.82 x 17.98 in installed 11.75 x 22 x 19 in, with 12 x 22 in a field 11.8 x 15.7 x 6.2 in 15.5 x 21 x 15.6 in
Cabinet opening the maker asks for not published A minimum 9 in opening A minimum opening width of 11.5 in At least 13 in wide and 17 in deep At least 16.5 in wide and 22 in deep
Tiers published Three Three tiers, four compartments Two steel baskets One Two, pulled out independently
Height adjustment published Five or more height settings not published not published not published Two height options for the lower basket
Handle published not published not published not published Premium leather handles not published
Material published Thicker heavier steel, a 1 in reinforced frame Epoxy coated steel, platinum finish Steel wire baskets Carbon steel with a powder coating Wire baskets
Cabinet type restriction not published Base cabinets Base kitchen cabinets, measure including hinges Frameless cabinets only, will not fit a framed door Base cabinets

What the table cannot tell you is the pull force. Five listings describe the slides as smooth, quiet or precision and not one publishes a figure for how hard the basket is to move. ClosetMaid is the only one that publishes soft close glides, which is a statement about the closing half of the movement and still not a number.

Sixty Pounds, Held On by Suction Cups

The One Load Figure Among These Five

PXRACK publishes the number this page is built on: the system holds up to 60 lbs effortlessly, with four large suction cups and two nano adhesive films for one set. It adds thicker heavier steel and a 1 inch reinforced frame, and states that the weighted design prevents wobbling. That is the fullest stability claim on this fact sheet.

The question a cautious reader will ask is what 60 lbs on suction cups means over a year in a damp under sink cabinet, and the listing does not address it. PXRACK also publishes 3 tiers with 5 or more height settings and states you can reach items at the back without bending or kneeling, which is the accessibility claim itself.

The Hundred Pound Figure We Left Out

There is a second load figure on this fact sheet and it belongs to something else. Youeon publishes a pull out trash can rack in chrome stainless that it states can withstand 100 pounds of weight, screwed to the cabinet floor with the included screws. It is the only 100 pound claim in these sixteen listings.

We left it out because it is a bin holder, not a basket, and a page recommending it for pots and cans would be recommending the wrong thing. It is worth reporting because it shows what a load figure looks like when the unit is screwed down: 100 pounds on screws against 60 on suction cups, and the difference is the fixing rather than the steel.

What Holds the Unit to the Cabinet

Adhesive, Suction Cups or Four Screws

Two of these five ask for no tools. Kitstorack states no measuring, screws, drilling or nails are needed and that you tear off the nano glue and install it where you like. PXRACK uses four suction cups and two adhesive films. Both are the easier installation and both put the load on a stuck surface.

The other three screw in. Rev-A-Shelf comes fully assembled and states a simple four screw installation, with optional door mount brackets sold separately. ClosetMaid includes a template giving the exact location and hardware to mount to the bottom cabinet space. OCG includes a step by step manual, a mounting template and all the hardware.

The Cabinet Each One Demands

The install method decides what cabinet you need, and the figures here are specific. Kitstorack states a unit of 11.8 by 15.7 by 6.2 inches and requires a cabinet at least 13 inches wide and 17 deep, and it is the only listing here that states it fits frameless cabinets only and will not fit a framed door.

OCG states 15.5 by 21 by 15.6 inches and asks for a net opening of at least 16.5 inches and a net depth of at least 22. ClosetMaid asks for a minimum 9 inch opening. Rev-A-Shelf publishes a minimum opening width of 11.5 inches in its title and tells you to measure including the hinges.

Slides, Soft Close and a Listing With Four Sizes

The Only Soft Close on the Page

ClosetMaid publishes the phrase that matters for a hand that cannot catch a heavy drawer: ball bearing, full extension soft close glides. Nobody else among these five says soft close. Rev-A-Shelf publishes a full extension ball bearing system on each basket and states the organizer can be pulled all the way out of a cabinet.

Kitstorack publishes 3 stage full extension ball bearing slides and adds the only handle claim of these five, premium leather handles stated to add style and comfort. OCG publishes precision ball bearing slides and the feature nobody else has: the upper and lower baskets slide out independently, so one tier can stay put.

Rev-A-Shelf Publishes Four Different Sizes

The Rev-A-Shelf listing cannot decide what size it is. The title gives a minimum opening width of 11.5 inches. The size field says 12 inches wide by 22 deep. One bullet says 11.75 wide by 22 deep by 19 high. Another bullet says the 18 inch depth makes it perfect for maximizing cabinet space.

We have used the bullet that gives all three, 11.75 by 22 by 19 inches, and noted the rest. Its dimension fields read 12 by 1 by 22 inches, and a depth of 1 inch is not a two basket unit, so those were set aside. Rev-A-Shelf publishes 19.75 pounds, the heaviest unit of these five before a single pan goes in it.

Which One Fits Your Kitchen

You want a load figure and no drill. PXRACK publishes a 60 lb load held by four suction cups and two nano adhesive films, three tiers, five or more height settings, a 1 inch reinforced frame, and reaching the back without bending or kneeling.

The drawer must not slam shut. ClosetMaid publishes ball bearing full extension soft close glides, three tiers and four compartments, a minimum 9 inch cabinet opening, an installation template, epoxy coated steel, and 9.2 pounds of unit.

You want it screwed down and fully assembled. Rev-A-Shelf publishes two steel baskets on full extension ball bearing systems, a four screw installation, a stated 11.75 by 22 by 19 inch unit, a minimum opening width of 11.5 inches, and 19.75 pounds.

Kneeling is the problem you are solving. Kitstorack states you no longer need to be on your knees, publishes 3 stage full extension slides, leather handles, 6.2 inch sidewalls, nano glue instead of screws, and 4.61 pounds, the lightest unit of these five.

You want each tier to move on its own. OCG publishes upper and lower wire baskets that slide out independently on precision ball bearing slides, two height options for the lower basket, a stated 15.5 by 21 by 15.6 inch unit, and 12.9 pounds.

What We Could Not Verify

Every figure above is a maker’s own published number or sentence, taken from the listing itself. These are the things we went looking for across all sixteen listings on this fact sheet and could not find.

  • A load figure from four of these five, on units sold to carry pots, pans and appliances.
  • A pull force or a closing force from any of the sixteen listings on this sheet.
  • A unit size stated in words by PXRACK, whose only figures are a carton and a load.
  • Whether the Rev-A-Shelf unit is 11.5, 11.75 or 12 inches wide, since its own text gives all three.
  • How long an adhesive or suction fixing is stated to hold a load in a damp cabinet.
  • A cabinet opening figure from PXRACK, the one pick here that names none.

Frequently asked questions

How much weight will a pullout cabinet basket hold?+

Only one of these five says. PXRACK states its system holds up to 60 lbs effortlessly, with four large suction cups and two nano adhesive films for one set. Kitstorack claims excellent load bearing strength without a figure, and Rev-A-Shelf says heavy duty slides. ClosetMaid and OCG publish nothing about load. Elsewhere in this pool a trash can rack states 100 pounds, but that is a bin holder rather than a basket.

Can a pullout basket be installed without drilling?+

Two of these five say so. Kitstorack states no measuring, screws, drilling or nails are needed, and that you tear off the nano glue and install it where you like. PXRACK uses four suction cups and two adhesive films. The other three screw in: Rev-A-Shelf with four screws, and ClosetMaid and OCG with a template and hardware into the cabinet floor.

Which of these has soft close slides?+

ClosetMaid, and only ClosetMaid. Its bullet states ball bearing, full extension soft close glides. Rev-A-Shelf publishes a full extension ball bearing system on each basket, Kitstorack 3 stage full extension ball bearing slides, OCG precision ball bearing slides and PXRACK a smooth 3 tier sliding design. None of those four says anything about how the basket stops when it is pushed back in.

How big a cabinet do these need?+

Four of the five publish a figure. Kitstorack asks for at least 13 inches of width and 17 of depth, and states it fits frameless cabinets only. OCG asks for a net opening of at least 16.5 inches and a depth of at least 22. ClosetMaid asks for a minimum 9 inch opening. Rev-A-Shelf publishes a minimum opening width of 11.5 inches. PXRACK publishes none.

Why does the Rev-A-Shelf listing give several sizes?+

Because its own text does not agree with itself. The title gives a minimum opening width of 11.5 inches, the size field says 12 inches wide by 22 deep, one bullet says 11.75 wide by 22 deep by 19 high, and another mentions an 18 inch depth. Its dimension fields read a depth of 1 inch, which cannot be a two basket unit, so this page uses the bullet that gives all three figures.

Does the unit weight matter if it stays in the cabinet?+

It matters twice. It is what you hold up inside a cabinet while the screws or the adhesive go in, which is the hardest part of the job for anyone who cannot kneel comfortably. It is also mass already sitting on the slides, so a 19.75 pound unit is pulling that much before a pan is added. Kitstorack publishes 4.61 pounds at the other end.

Specifications come from the manufacturers' own published listings. Lush Food & Drink may earn a commission if you buy through a link on this page, at no extra cost to you. How we research.