Explainer
How do you clean avocado slicers?
Rinse an avocado slicer right after use before the flesh dries on, wash it in warm soapy water with a brush worked through the slots and around the pitter and blade, then dry it fully. Clean it promptly and it stays easy; let it dry on and it is a chore.
By the Lush Editorial Team·Researched & Compared
You clean an avocado slicer by rinsing it the moment you finish, before the soft flesh dries into the slots, then washing it in warm soapy water with a small brush worked through the slicing slots and around the pitter and the blade, and drying it fully. Avocado is oily and clings, so the single most important habit is cleaning it promptly: done straight away it takes seconds, left to dry it turns into stubborn green gunk wedged in the gaps. Our Best Avocado Slicers compares five of them.
Rinse it straight away
The whole difference between an easy clean and a fiddly one is timing. Avocado flesh is soft and fatty, and while it wipes off effortlessly when fresh, it dries to a tacky film that grips the plastic or metal and lodges in the narrow slicing slots. Rinsing the slicer under warm running water the moment you are done lifts most of the flesh before it has a chance to set.
This matters most with the three working parts of a typical slicer: the slicing fan of thin blades or wires, the scoop, and the pitter with its sharp points or cutting edge. Each has gaps and corners that trap flesh, so a quick rinse that flushes those gaps while everything is still wet saves you digging it out later with a toothpick.
Washing the working parts
For the proper wash, use warm water and a little dish soap with a small brush, a bottle brush, a dish brush or an old toothbrush, which reaches into the slicing slots far better than a flat sponge that just slides over the top. Work the bristles along each slot and around the scoop so no film is left where it would go slimy or smell.
Pay particular attention to the pitter, as the flesh packs tightly around its points and into the center, and to the join where the blade meets the handle, a classic hiding spot for trapped food. Take care around the slicing blades and pitter points while you do this, washing with the brush rather than running a bare finger along a sharp edge. Turn the slicer over and rinse from both sides to flush loosened bits clear.
Dishwasher or hand wash
Many avocado slicers are dishwasher safe, usually on the top rack, and the machine’s hot water does handle the oily residue well. The catch is that a dishwasher spray does not always reach inside the narrow slicing slots, so flesh wedged there can survive a cycle and bake on harder, which is why a quick rinse before loading still helps even if you machine wash.
Hand washing gives you more control over those awkward gaps and is kinder to any slicer with a wooden handle or non-stainless blade, which can suffer in repeated hot cycles. If a model’s instructions say hand wash only, follow that, since forcing a non-dishwasher slicer through the machine can dull a blade or split a handle. For most people a rinse plus a brief hand wash is the quickest reliable route.
Drying, storage and stains
Dry the slicer fully before putting it away, because trapped water in the slots and around the pitter can leave spots on metal and lets any missed residue turn musty in a drawer. A shake and a towel, then a few minutes air drying with the parts separated if the slicer comes apart, is enough. Store it where the blades and pitter points are protected and will not catch your hand in the drawer.
Avocado can leave a faint green or brown stain on light-colored plastic over time, which is cosmetic and harmless. If it bothers you, a soak in warm water with a little baking soda, or a paste of baking soda rubbed on with a brush, lifts most of it, and keeping the slicer out of prolonged direct sun helps too. The key point throughout is speed: clean it right after use and an avocado slicer is one of the easier gadgets to keep spotless.
The short answer
To clean an avocado slicer, rinse it under warm water the moment you finish, before the oily flesh dries into the slicing slots, then wash it in warm soapy water using a small brush worked through the slots and around the scoop, the pitter points and the blade join where food hides, taking care around the sharp parts. Rinse from both sides, then dry it fully to avoid spots and musty residue, and store it with the blades protected. Many slicers are dishwasher safe on the top rack, but a spray does not always reach inside the slots, so a quick rinse first helps either way. Clean it promptly and it takes seconds; let the flesh dry on and it becomes a chore.
Common questions
How do you clean an avocado slicer?
Rinse it under warm water the moment you finish, before the flesh dries into the slots, then wash it in warm soapy water with a small brush worked through the slicing slots and around the scoop, pitter and blade join. Rinse from both sides, taking care around the sharp parts, and dry it fully. Cleaning it promptly keeps the job to seconds.
Why is my avocado slicer hard to clean?
Almost always because the flesh dried on. Avocado is soft and oily, so it wipes off easily when fresh but sets into a tacky film that grips the slots and the pitter if left. Rinsing straight after use prevents it. Once dried, a soak in warm soapy water and a brush or toothbrush worked into the gaps loosens the stuck residue.
Are avocado slicers dishwasher safe?
Many are, usually on the top rack, and the hot water deals with the oily residue well. The catch is that a dishwasher spray does not always reach inside the narrow slicing slots, so flesh wedged there can survive and bake on. A quick rinse before loading helps. Check the maker's note, as wooden handles and non-stainless blades may be hand wash only.
How do I remove avocado stains from a slicer?
A green or brown stain on light plastic is cosmetic and harmless. To lift it, soak the slicer in warm water with a little baking soda, or rub on a baking soda paste with a brush and rinse. Keeping the slicer out of prolonged direct sun helps prevent stains setting. The stain does not affect how the slicer works, only how it looks.
What is the best way to clean the pitter part?
Use a small brush or old toothbrush, since the flesh packs tightly around the pitter points and into the center where a sponge cannot reach. Rinse it first to flush out the bulk, then work the bristles around the points and the base, washing rather than running a bare finger along the sharp edges. Dry it fully so no water spots the metal.
Ready to compare actual models?
Our buying guide puts five products side by side on the numbers their makers publish.