Lush Food & Drink

Explainer

How do you use canning clamps?

Canning clamps hold a lid flat on a jar during processing, and the maker's published figures for the canners that work with them are limited to capacity and dimensions.

By the Lush Editorial Team·Researched & Compared

Canning clamps are small metal clips that hold a flat lid or glass lid down on a jar while it is processed, and you fit them over the rim before the jar goes into the canner. They are used with jars that have no screw band, so the clamp does the holding and the lid is removed or sealed after processing. The makers of the canners in our guides publish capacity and dimension figures, and those figures tell you which canner holds the jars you plan to clamp.

Nothing on this site has been used or measured. What follows is what each maker states about its canner and what that means for loading clamped jars.

What a canning clamp does

A clamp sits over the rim of the jar and presses the lid down evenly. The spring in the clip keeps tension while the jar is in the water bath or pressure canner, so the lid stays put and the contents stay covered. After processing, the clamp comes off and the lid is either sealed with a band or replaced, depending on the jar type.

Clamps are not part of any canner on our fact sheets. No maker in the Best Electric Canners for Pressure and Water Bath Preserving guide lists clamps among included accessories. The NESCO NPC-9 lists a canning rack and a steam rack, and the WantJoin water bath canner lists a steam rack, jar lifter, funnel and measuring tool. Clamps are a separate item you supply.

The practical point is that a clamp adds a little height and a little width at the jar rim. That matters when you stack jars in a rack or fit them under a lid, so check the jar count a maker publishes before you plan a batch.

Loading clamped jars in an electric canner

The NESCO NPC-9 is listed at 9 Quarts with a 9.5-quart removable nonstick inner pot, and the maker states it includes canning and steam racks. Clamped jars sit on the rack, not on the pot bottom, so the rack is what you load. The maker does not publish a jar count for this model, so this site has not compared how many clamped jars fit.

The Presto 02144 is listed at 12 Quarts. Presto states it automates both pressure canning and water bath canning and that no adjustments are needed for high altitudes. The maker does not publish a jar count for this model either, so the number of clamped jars per batch is not something this site can state.

The WantJoin water bath canner is listed at 33Qt in the title and 30 Quarts in its feature text, and the maker states it holds up to 11 one-quart jars. That is the clearest jar figure in the electric guide. Clamps add height at the rim, so load the rack and check clearance under the lid before you process.

Clamps in a stovetop pressure canner

The Presto 01784 is listed at 24.3 Quarts, and Presto states space for 7 quarts, 20 pints, or 26 half-pints of regular Mason jars. The maker also states an air vent and cover lock that lets pressure build only when the cover is properly closed. Clamped jars go on the rack, the cover goes on, and the lock does the rest.

The All American 921 is listed at 21.5 Quarts, and the maker states it holds about 19 pint jars or 7 quart jars. All American states a metal-to-metal sealing system with positive action clamping locks that form a steam-tight seal without gaskets. Those are the canner’s own clamps, not jar clamps, so do not confuse the two when you read the listing.

The Siftary 24 QT canner is listed at 24 Quarts and the maker states a 14.5 PSI gauge plus 2 stainless steel racks and 1 aluminum rack. The maker does not publish a jar count. The RVGMBO 12 Quart and the Hestroney 10.6 Quarts also publish no jar count, so this site has not compared clamped jar capacity for either.

Fitting and removing the clamps

Fill the jar, wipe the rim, set the lid flat, and fit the clamps evenly around the rim so the lid sits level. Load the jars onto the rack in the canner, leaving space between them so water or steam can move. Lower the rack, close the canner, and run the cycle the maker’s controls provide.

On the Presto 02144, the maker states a digital interface with a control knob to select the canning method and time, and LED icons that illuminate each stage. On the NESCO NPC-9, the maker states a digital display with preset programs and a timer. Set the cycle, then leave the lid alone until the canner says the pressure is down.

When processing ends, wait for pressure to drop before opening. The NESCO maker states a safety lock lid and automatic float valve that prevent opening under pressure. The Presto 01784 maker states the cover cannot open until pressure is safely reduced. Remove clamps only after the jars are out and cool enough to handle.

Water bath depth and lid clearance

In a water bath canner, the water needs to cover the jars, and a clamp raises the top of each jar slightly. The McSunley Prep•N•Cook is listed at 21.5 Quarts, and the maker states its easy-lift jar rack holds 7 one-quart, 9 one-pint or 12 half-pint jars and keeps jars off the bottom for full water circulation. That rack is the reference point for loading.

The WantJoin maker states adjustable temperature from 86 to 212 degrees Fahrenheit and a timer from 30 to 180 minutes, with a built-in thermal sensor. Those are the maker’s published settings for the water bath, and they apply to whatever jars you load, clamped or not. The maker does not publish a water depth figure.

For pressure models, clearance under the cover matters more than water depth. The Presto 01784 maker states heavy-gauge aluminum with an induction-compatible stainless steel clad base. The All American maker states a steam gauge and a machined regulator weight. Neither publishes interior height, so this site has not compared clamp clearance.

Common questions

Are canning clamps the same as the clamps on a pressure canner lid?

No. Jar clamps are small clips that hold a lid on a single jar. The clamping locks on the All American 921 are part of the canner's metal-to-metal sealing system, which the maker states forms a steam-tight seal without gaskets. The two are different parts and are not interchangeable.

Can I use clamps in an electric water bath canner?

Yes, if the jars fit on the rack and clear the lid. The WantJoin maker states the canner holds up to 11 one-quart jars and includes a steam rack, jar lifter and funnel. The maker does not publish interior height, so this site has not compared clamp clearance for that model.

How many clamped jars fit in a Presto 01784?

Presto states space for 7 quarts, 20 pints, or 26 half-pints of regular Mason jars in the 24.3-quart canner. Those figures are for standard jars without clamps. The maker does not publish a jar count for clamped jars, so this site has not compared that.

Do I need a rack under clamped jars?

Yes. The McSunley maker states its rack keeps jars off the bottom for full water circulation, and the NESCO NPC-9 and Siftary 24 QT both list racks as included. Sitting jars directly on the pot bottom is not what any of these makers describes.

When do the clamps come off?

After processing and after the jars are out of the canner and cool enough to handle. The NESCO maker states a safety lock lid and automatic float valve that prevent opening under pressure, and the Presto 01784 maker states the cover cannot open until pressure is safely reduced. Follow that before you touch a jar.

Does any canner in these guides include jar clamps?

No. The NESCO NPC-9 lists a canning rack and steam rack, and the WantJoin lists a steam rack, jar lifter, funnel and measuring tool. The Siftary lists a 7-piece kit with a lid lifter, jar wrench, tongs, funnel, stirrer and rack. Clamps are not on any of those lists.

Ready to compare actual models?

Our buying guides put five products side by side on the numbers their makers publish.

More questions about electric canners