Explainer
What should I do if my cutting board has mold?
Discard a moldy wooden or bamboo board if the growth has gone into the grain, and clean a nonporous plastic or titanium board with hot soapy water and a disinfecting rinse, then dry it fully.
By the Lush Editorial Team·Researched & Compared
If the mold is on a plastic or titanium board, wash it with hot soapy water, rinse, and dry it completely before storing. If the mold is on a wooden or bamboo board and has worked into the grain, cracks, or seams, stop using it for food: wood is porous and the growth can sit below the surface where washing does not reach.
The reason mold appears at all is moisture. Every board on this site’s guides is stored, cleaned, or dried in some way, and the makers’ own care notes are the best guide to keeping a board dry between uses.
Why mold grows on a cutting board
Mold needs moisture, food residue, and time. A board that is rinsed and put away wet, or left flat on a counter with water pooled in a juice groove, gives spores a place to settle. Plastic and titanium surfaces are nonporous, so growth sits on top and can be washed away. Wood and bamboo are porous, so moisture and residue can move below the surface.
The makers describe their surfaces in these terms. The GORILLA GRIP BPA-Free Reversible Kitchen Cutting Board set, one of the picks in Best Cutting Boards for Plastic and Titanium Sets, is described as having a nonporous surface that helps prevent liquid and odor absorption. The Sumzzz Titanium Cutting Board, from the same guide, is described as having a non-porous titanium surface that helps reduce the absorption of liquids, odors, and stains.
Wooden boards are a different case. The Bevel & Bond Maple End-Grain Cutting Board, a pick in Best Meat Cutting Boards for Carving Roasts and Raw Prep, is described as resisting staining and odors through its tight maple grain, and the maker states it should be hand washed with warm soapy water, towel dried, never soaked, and never put in a dishwasher.
Cleaning mold off a plastic or titanium board
Scrub the whole board, both faces and the edges, with hot soapy water and a brush that can reach into any groove. Rinse and dry it fully before it goes back in the cabinet. Several picks are dishwasher safe, which the makers state directly: the THETCHRY Plastic Cutting Board Set and the Empune Extra Large Cutting Boards, both in Best Cutting Boards for Plastic and Titanium Sets, are described as dishwasher safe, and so is the OXO Good Grips Plastic Utility Cutting Board in Best Meat Cutting Boards for Carving Roasts and Raw Prep.
For a titanium board, the Pexucalm Double-Sided Titanium Cutting Board, a pick in Best Cutting Boards for Plastic and Titanium Sets, is described by its maker as having a titanium surface with natural non-stick properties that lets grease and meat juices rinse off, with a quick wipe with a dishcloth described as enough to clean it. That is the maker’s statement about grease and juices, not a mold claim, so treat visible mold as a reason for a full soap-and-water wash and a complete dry.
If mold keeps returning to the same plastic board after washing and drying, the growth is likely in knife scars that the brush cannot reach. A board with deep, dark scoring is a candidate for replacement rather than another wash.
What to do with a moldy wooden or bamboo board
Look at where the mold sits. Surface specks on a well-sealed board can sometimes be scrubbed away and the board dried thoroughly, but growth that follows a crack, a glue seam, or a dark ring into the wood means the board should be retired from food use. The makers of the wooden picks describe sealed, moisture-resistant surfaces, and those finishes are what keep water out in normal use.
The ROYAL CRAFT WOOD set, a pick in Best Wooden Cutting Boards for Juice Grooves and Storage, is described as having a protective finish that prevents water and odor absorption, with hand washing in mild soap and warm water recommended. The Allsum Extra Thick Wood Cutting Board, from the same guide, is described as deep carbonized bamboo that reduces moisture absorption and resists cracking and splintering, and the maker states it should be hand washed, kept out of the dishwasher, and stored in a cool dry place.
None of these makers publishes a mold removal procedure, and this site has not compared one. Where a maker publishes no guidance on mold, the safe reading of a porous board with growth below the surface is replacement.
Drying and storing boards so mold does not return
Dry a board standing on edge, not flat, so air reaches both faces. Store it the same way. The HzTinT Cutting Board and Baking Tray Cookie Sheet Organizer, a pick in Best Cutting Board Organizers for Thick and Thin Boards, is described as holding boards upright with 12 adjustable dividers whose widths range from 0.7 to 3.07 inches, and it can be set from 11.3 to 22.5 inches long.
The KORRTFID Cutting Board Storage Rack, from the same guide, is described as having four slots of 1.0 inch width, and the maker states it is not suitable for utensils thicker than 1.0 inches. The SUNFICON Cutting Board Rack, also in that guide, is described as holding boards from 0.85 to 1.1 inches wide, and the LAEMYFYRE Cutting Board Holder Stand is described as having 1.0 and 1.2 inch wide slots. An upright rack lets a board air dry on both faces, which is the point.
Wooden boards also need occasional conditioning. The Bevel & Bond maker states the board arrives pre-conditioned and needs a monthly conditioning with its Board Balm, and the Kikcoin Extra Large Bamboo Cutting Board in Best Wooden Cutting Boards for Juice Grooves and Storage is described as finished with mineral oil, with hand washing recommended. A conditioned surface sheds water rather than drinking it.
Habits that keep mold from starting
Wash and dry the board the same day it is used, especially after raw meat. The OXO Good Grips Plastic Utility Cutting Board, a pick in Best Meat Cutting Boards for Carving Roasts and Raw Prep, is described as double sided with non-porous surfaces that resist odors, and it has a drip catcher and easy-pour corners, which keeps liquid on the board and off the counter where it can sit.
Use separate boards for meat and produce so residue does not collect in one place. The THETCHRY set is sold as three sizes, 15 by 10 inches, 11 by 8 inches, and 9 by 6 inches, and the maker describes using the large one for meat and fish and the smaller ones for vegetables and fruit. The Empune set lists an extra large board at 17.0 by 11.8 by 0.4 inches, a large at 14.0 by 9.5 by 0.35 inches, and a medium at 11.4 by 7.8 by 0.35 inches.
Finally, never soak a wooden board and never leave any board sitting in water. The Realgulf 24×18 Teak Butcher Block, a pick in Best Meat Cutting Boards for Carving Roasts and Raw Prep, is described as hand wash only, with regular mineral oil conditioning to keep the wood smooth, and its maker states that dense edge-grain teak slows moisture intake to keep the board flat.
Common questions
Can I sand mold out of a wooden cutting board?
No maker in this site's guides publishes a sanding or refinishing procedure for mold, and this site has not compared one. Sanding removes surface wood, but growth that has followed a crack or seam can sit deeper than the sanded layer. If the mold returns after cleaning and full drying, retire the board from food use.
Is a moldy plastic cutting board safe after the dishwasher?
A dishwasher cycle with hot water and a full dry is the strongest cleaning step the plastic picks offer, and the THETCHRY, Empune, and OXO makers all state their boards are dishwasher safe. If dark growth remains in deep knife scars after the cycle, the board is a candidate for replacement rather than another wash.
Why does mold keep coming back on the same board?
Moisture is staying in the board or in the storage spot. A board stored flat, stacked, or put away damp holds water against its face. An upright rack such as the SUNFICON, which holds boards from 0.85 to 1.1 inches wide, lets air reach both faces, and a wooden board benefits from the monthly conditioning its maker describes.
Should I oil a board to stop mold?
Oil slows water uptake on wood, which is why the Bevel & Bond maker states a monthly conditioning with Board Balm and the Kikcoin maker describes a mineral oil finish. Oil is not a mold treatment, and no maker in these guides publishes one. Oil a clean, fully dry board, never a damp one.
Does a juice groove make mold more likely?
A groove holds liquid if the board is left flat, so empty and dry it after washing. The Empune maker describes a juice groove on all sides to catch liquids, and the Pexucalm maker describes a deep juice groove on its wheat straw side. Both are easier to dry than a flat face only if the board is stood on edge.
Ready to compare actual models?
Our buying guides put five products side by side on the numbers their makers publish.