Lush Food & Drink

Explainer

How do you apply cutting board wax?

Rub a thin, even coat of board wax or board balm into a clean, dry board, let it soak in, then buff off the excess.

By the Lush Editorial Team·Researched & Compared

Apply cutting board wax by rubbing a thin, even coat into a clean, dry board with a cloth, letting it sit so the wood takes it in, then buffing off the excess with a dry cloth. Work with the grain and keep the layer light, because a thick coat sits on the surface and stays tacky instead of soaking in.

Wax is a top coat for wood and bamboo boards, not a finish for plastic or titanium. The picks in our guides show the range of surfaces a kitchen holds, from the dense end grain of a maple block to the nonporous face of a plastic board, and each takes a different kind of care. The steps below cover the wood and bamboo boards, then explain what the other materials need instead.

What you need before you start

You need a board wax or a wood conditioner such as a board balm, a clean lint-free cloth, a second dry cloth for buffing, and mild soap and warm water for the wash first. Some makers ship a conditioner with the board. Bevel & Bond states that its maple end-grain board arrives pre-conditioned and ready to use, and that registering the board brings a complimentary tin of Board Balm. If your board came with a balm, use that, since the maker formulated it for that wood.

Skip anything that is not made for wood. Cooking oil, olive oil and similar kitchen fats can turn rancid in the grain over time, and a maker that publishes a care routine names a wood conditioner rather than a food oil. Read the label on the wax or balm and follow the maker’s directions for how long to leave it on, since soak times differ between products.

The board itself should be dry before wax goes on. Wash it by hand with mild soap and warm water, rinse, and towel dry, then let it air dry fully so no moisture sits in the grain. Wax over a damp board traps water under the coat.

How to apply the wax in four steps

First, lay the dry board flat on a counter with a towel underneath to catch drips. Second, scoop a small amount of wax onto the cloth and rub it into the surface in the direction of the grain, covering the face, the edges and the sides. Third, let the board sit so the wood absorbs the wax, for the time the wax maker specifies. Fourth, buff the whole surface with a clean dry cloth until the film is gone and the board feels smooth rather than sticky.

Repeat on the other face if the board is reversible, and give the edges the same thin coat, since end grain at the edges drinks wax faster than the flat faces. A board with a juice groove needs the groove wiped out with the cloth too, because wax pools in the channel. Wipe away any wax that gathers in a corner or a handle cutout rather than leaving a lump.

Work in a thin layer and add a second only where the wood still looks dry after buffing. Two thin coats beat one heavy coat, and the buffing step is what removes the surplus that would otherwise collect dust and feel greasy under the hand.

How often to wax, and how to tell the board needs it

Wax when the surface starts to look dry, pale or thirsty, and after any deep clean. Bevel & Bond describes a quick monthly conditioning with Board Balm as all its maple board needs to stay in peak shape. Realgulf states that regular mineral oil conditioning keeps its teak board smooth for daily heavy use. Those two makers set the rhythm: a light routine on a schedule, more often on a board that sees daily work.

A simple check is to sprinkle a few drops of water on the face. On a well-waxed board the water beads; on a dry board it soaks in quickly. If it soaks in, the board is ready for another coat. The same test tells you when the coat is still good and you can leave the board alone.

Wax is not a repair. A board with a deep scratch, a split or a raised grain needs sanding before it needs wax, and a board that has warped needs the maker’s advice. Wax maintains a sound surface; it does not fix a damaged one.

Which wood and bamboo boards in our guides take wax

Our guide to the best wooden cutting boards covers boards that benefit from a wax or oil routine. The Kikcoin Extra Large Bamboo Cutting Board is finished with mineral oil, per the maker, and the maker recommends hand washing to keep it in condition. The Allsum Extra Thick Wood Cutting Board is 1 inch thick with a three-layer build, and the maker directs hand washing under running water, no dishwasher, and storage in a cool dry place. The ROYAL CRAFT WOOD set is sealed bamboo, and the maker asks for hand washing with mild soap and warm water.

Our guide to the best meat cutting boards includes the heaviest wood in the group. The Bevel & Bond Maple End-Grain Cutting Board measures 17 x 13 inches and 1.75 inches thick, weighs 10 pounds, and arrives pre-conditioned with a mineral oil finish. The maker states it should be hand washed with warm soapy water and towel dried, never soaked and never put in a dishwasher. The FANICHI End Grain Cutting Board is 17 x 13 inches and 1.5 inches thick, and the maker notes that with proper care it will outlast most kitchen tools. The Realgulf 24×18 Teak Butcher Block is 1 inch thick and hand wash only, with mineral oil conditioning named for daily heavy use.

Wax suits all of these because they are wood. Follow each maker’s own wash and care line first, then add the wax coat on top of a fully dry board.

Plastic, bamboo sets and titanium: what not to wax

Plastic boards do not take wax, and their makers say so in different words. GORILLA GRIP states that its boards need no oiling or special maintenance, and that the nonporous surface resists liquid and odor absorption. The THETCHRY set is food-grade plastic and dishwasher safe, and the Empune set is high-density plastic that rinses with warm water or goes in the dishwasher. Wax on these surfaces would sit on top and smear, so wash them and skip the wax.

Titanium is the same story. The Sumzzz Titanium Cutting Board has a nonporous titanium face that the maker says reduces absorption of liquids, odors and stains, and both sides rinse clean with water. The Pexucalm Double-Sided Titanium Cutting Board pairs a titanium side with a wheat straw PP side, and the maker describes the titanium as naturally non-stick, cleaned with a quick wipe. Neither maker publishes a wax or oil routine, and neither surface needs one.

Bamboo sets sold as a group, such as the ROYAL CRAFT WOOD and Astercook sets, are wood at heart and do take a conditioner, but check the maker’s care line before you start. Astercook describes its boards as deep-carbonized bamboo that resists water absorption, and the maker’s care guidance should be read before any finish goes on.

Drying and storing a waxed board

Let a freshly waxed board sit flat or stand on edge in open air so the coat settles, and give it a few hours before the next wash. Do not stack it against another board while the wax is still soft. Our guide to the best cutting board organizers covers racks that hold boards upright and apart. The SUNFICON rack measures 4.92 x 5.7 x 8.47 inches with dividers 1.18 inches wide, and the maker says it holds boards from 0.85 to 1.1 inches wide. The LAEMYFYRE stand measures 6.1 x 6.1 x 4 inches with 1.0 and 1.2 inch slots.

An upright rack lets air reach both faces of a waxed board, which keeps the coat even and stops one side sitting damp against a counter. The HzTinT organizer adjusts from 11.3 to 22.5 inches and has dividers from 0.7 to 3.07 inches wide, so it can hold a thick butcher block alongside thinner boards. The KORRTFID rack has four slots 1.0 inch wide and the maker notes it is not suited to items thicker than 1.0 inch.

Store waxed boards away from direct sun and away from a hot stove, since heat softens the coat. A board kept dry, upright and out of heat holds its wax longer, and the next coat goes on faster because the wood has stayed conditioned.

Common questions

Can I use cooking oil instead of cutting board wax?

Use a product made for wood, such as a board wax or a board balm. Kitchen oils can turn rancid in the grain over time. Bevel & Bond names Board Balm for its maple board, and Realgulf names mineral oil conditioning for its teak block. Follow the conditioner the maker names rather than a food oil from the cupboard.

Do I need to wax a plastic or titanium cutting board?

No. GORILLA GRIP states its plastic boards need no oiling or special maintenance, and the THETCHRY and Empune plastic sets are washed by hand or in a dishwasher. The Sumzzz and Pexucalm titanium boards rinse clean with water, and neither maker publishes a wax or oil routine. Wax belongs on wood and bamboo.

How much wax should I put on a board?

A thin, even coat. Rub a small amount into the grain with a cloth, let it soak in for the time the wax maker specifies, then buff off the excess with a dry cloth. Add a second thin coat only where the wood still looks dry. A heavy coat stays tacky and collects dust.

Should I wax the edges and the juice groove?

Yes. Give the edges and the sides the same thin coat, since end grain there absorbs wax faster than the flat faces. Wipe the juice groove out with the cloth so wax does not pool in the channel, and clear any wax that gathers in a handle cutout or a corner.

How do I know when the board needs another coat?

Sprinkle a few drops of water on the face. If the water beads, the coat is still good. If it soaks in, the board is dry and ready for another thin coat. Bevel & Bond describes a quick monthly conditioning, and Realgulf names regular mineral oil conditioning for daily heavy use.

Can I wax a board that has cracks or deep scratches?

Wax maintains a sound surface and does not repair damage. A board with a deep scratch, a split or raised grain needs sanding before it needs wax, and a warped board needs the maker's advice. Fix the surface first, then apply a thin coat to protect it.

Ready to compare actual models?

Our buying guides put five products side by side on the numbers their makers publish.

More questions about cutting boards