Explainer
Should water cover jars in a pressure canner?
Yes: jars in a pressure canner sit in water, but the water should come partway up the jars, not over the lids, and the maker's own manual sets the depth.
By the Lush Editorial Team·Researched & Compared
No, water should not cover the jars in a pressure canner. The jars stand on a rack with water around their lower portion, typically a few inches deep, and the lids stay above the waterline so steam, not boiling water, does the work under pressure.
That is the short answer, and it holds for every pressure canner on this site’s Best Pressure Canners for Large-Batch Home Canning guide. What the makers publish about depth varies, and the canner’s own instruction book is the authority for your model. This page covers what the published figures do and do not tell you.
Why the water stops below the lids
A pressure canner works by trapping steam. Once the lid is locked and the canner is heated, the small amount of water at the bottom turns to steam, the air is vented out, and pressure builds. The steam surrounds the jars and transfers heat to the food inside. If the jars were submerged, the water would have to boil for the contents to reach canning temperature, and the pressure gauge would be reading a pot of boiling water rather than a steam environment.
The rack matters as much as the depth. Every canner in the pressure guide that lists a rack describes jars held off the bottom, so water circulates under and around them and the glass never sits directly on a hot base. The Presto 01784 23-Quart Induction Compatible Pressure Canner is listed at 17.5 inches wide, 13.5 inches deep and 15.5 inches tall, with space for 7 quarts, 20 pints or 26 half-pints of regular Mason jars. Those capacity figures describe jar counts, not water depth.
What the makers do not publish, in the features this site has compared, is a water level in inches or quarts for any of the five pressure canners. Presto, All American, RVGMBO, Siftary and Hestroney all describe capacity and safety systems, and none of the listed bullets states how deep the water should be. Follow the manual that ships with your canner.
What the pressure canner makers do publish
The published figures are about size, capacity and pressure control. The All American 921 is listed at 15.0 inches wide, 16.0 inches deep and 17.0 inches tall, weighing 20.0 pounds, and its bullets state it holds approximately 19 pint jars or 7 quart jars. It uses a metal-to-metal seal with no gasket, plus a steam gauge and a machined regulator weight for pressure control.
The Siftary 24 QT Pressure Canner is listed at 24 quarts with a gauge calibrated to 14.5 PSI, and its bullets describe two stainless steel racks plus one aluminum rack for a three-tier configuration. The RVGMBO 12 Quart model lists adjustable pressure from 15 PSI at HIGH to 10 PSI at LOW. The Hestroney is listed at 10.6 quarts. None of these bullets gives a water depth, and none states a maximum fill line in inches.
That absence is normal. Water depth depends on jar size, how many jars are loaded and the canner’s interior height, so makers put it in the manual rather than the product listing. A canner holding 7 quart jars and one holding 20 pints need different amounts of water to reach the same working level.
Jar size changes the water level
Taller jars displace more water, so a load of quart jars needs less water added than a load of half-pints to reach the same point on the jar wall. The jar sets in this site’s Best Canning Jar Sets for Water Bath and Steam Canning guide show the range. The ELAORY Classic 16 Oz Mason Jars are listed at 3.2 inches wide, 5.5 inches deep and 3.2 inches tall, with a stated size of 3.2 x 4.5 x 5.5 inches and a weight of 0.59 pounds. The Mcupper 16oz Regular Mouth Mason Jars are a 15-pack listed at 8.36 pounds with a 2.59 inch regular mouth.
Pint jars like these sit lower in the canner than quarts, so the same water volume reaches higher up the jar. That is one reason a fixed depth figure would mislead. The practical rule from the makers’ manuals is to fill to the level specified for your jar size, keep the lids clear of the water, and never let the canner run dry during the processing time.
The jar sets guide also lists the UONMAY 20 Quart Stainless Steel Stock Pot kit at 12.0 inches wide, 12.0 inches deep and 11.2 inches tall, weighing 7.0 pounds, and the Pisol Canning Supplies Starter Kit with a stainless steel rack listed at 11.65 inches wide, 11.65 inches deep and 2.95 inches tall. Those are pot and rack dimensions, not water levels.
How this differs from a water bath canner
A water bath canner is the opposite case: the jars are covered by water, usually by an inch or two, and the water is kept at a rolling boil for the whole process. That method is for high acid foods. The Best Water Bath Canners for High Acid Preserving guide lists pots built for that job. The McSunley Prep•N•Cook is 21.5 quarts, listed at 14.2 inches wide, 14.2 inches deep and 11.2 inches tall, weighing 11.11 pounds, with a rack that holds 7 one-quart, 9 one-pint or 12 half-pint jars.
The KITCHEN CROP Harvest Stainless Steel 20 Qt Canning Pot is listed at 17.5 inches wide, 13.1 inches deep and 11.5 inches tall, weighing 10.1 pounds, and its bullets state room for 8 pint or 7 quart jars. The Kendane 21.5QT pot is listed at 15.0 inches wide, 15.0 inches deep and 9.8 inches tall, weighing 10.8 pounds. The JY COOKMENT 21.5 Quart pot is listed at 16.5 inches wide, 16.5 inches deep and 12.4 inches tall, weighing 8.5 pounds.
These are water bath vessels, and their racks hold jars under water. A pressure canner uses the same rack idea but a different water level, because pressure, not submersion, is doing the preserving. Do not carry a water bath habit over to a pressure canner and fill it to the top.
Practical checks before you lock the lid
Set the rack in first, then the jars, then add water to the level your manual gives. Keep the water below the jar lids. Check that the canner’s vent is clear and that the lid locks as the maker describes. The Presto 01784 bullets describe an air vent and cover lock that lets pressure build only when the cover is properly closed and prevents opening until pressure drops. The RVGMBO lists a secure-lock lid, safety valve, lid window and pressure release valve. The Siftary lists dual over-pressure relief valves.
Those safety systems assume the canner is loaded as designed, with water at the correct level. Too little water risks scorching the base and running dry before the process ends. Too much water can bubble into the vent or splash the jars. Neither extreme is described in any published figure this site has compared, so the manual is the only reliable source.
If your canner’s manual is lost, contact the maker. This site has not tested any of these canners and cannot state a water depth for them. What it can state is the published capacity, dimensions and pressure settings, and those are on the guide pages linked above.
Common questions
Does the water in a pressure canner need to boil?
The water at the bottom comes to a boil as the canner heats, which is what generates steam. The jars themselves are not boiled in a deep bath the way they are in a water bath canner. Pressure builds once the air is vented, and the steam at pressure does the preserving. Keep the water level where the maker's manual puts it.
Can I stack jars in a pressure canner?
Some makers publish stacked capacities. The Presto 01784 lists space for 7 quarts, 20 pints or 26 half-pints, and the Siftary lists a three-tier rack setup. Stacking requires a rack between layers so jars do not rest on jar lids. Follow the loading instructions for your model, and keep the water below the lowest lid line.
What happens if the canner runs dry?
Running dry means no steam is being generated and the base can overheat, which risks damage to the canner and to the jars. The safety valves and locks on models like the RVGMBO and Siftary are designed for normal operation, not for a dry pot. Start with the water amount your manual specifies and do not open the canner mid process.
Is the water level the same for pint and quart jars?
No. Taller jars displace more water, so the same volume reaches a different height on the jar wall. A load of quart jars and a load of half-pints need different amounts of water to reach the working level. Check the manual for each jar size you run, and keep the lids above the waterline in both cases.
Do I add water to a pressure canner before or after loading jars?
Load the rack and jars first, then add water to the level the manual gives. Adding water first makes it harder to judge the level once jars displace it. Check that the vent is clear and the lid seats properly before heating, since the cover lock on models like the Presto 01784 depends on a correct close.
Ready to compare actual models?
Our buying guides put five products side by side on the numbers their makers publish.